Introduction of End Cover of Train Traction Motor Cover

The end motor cover of the train traction motor is used to close the motor and support the rotor. A cooling air inlet is provided on the upper part of the end cover of the non-transmission end, and a plurality of large holes are provided on the end cover of the transmission end as an air outlet. The rotor core is made up of silicon steel sheets with good magnetic conductivity, and there are 46 grooves in the outer circumference. There are ventilation holes on the core to dissipate heat and reduce mass. Both ends of the rotor core are equipped with pressure rings. The traction motor is mechanically fixed together through the threaded holes on the front and rear end covers and the bracket with the lifting spring. Profiles connect the spring brackets to form a rectangular lifting structure. When the motor is installed, the overall tilt to the driving end is 1.5°. The mechanical connection of the motor to the vehicle is achieved by means of a bracket with elastic suspension. Motion is transmitted to the wheel sets of the train via an appropriate cardan shaft and gearbox. The traction motor is mechanically connected to the cardan shaft by a safety device that protects the cardan shaft and gearbox from over-torque in the event of a short circuit between the two-phase coils of the traction motor. In the efficient operation of the traction motor, the end cover is a key support component, and its performance is directly related to the reliability of the motor, life and environmental adaptability.

The Function Orientation of The Traction Motor Cover

As a simple protective motor cover, but in fact it takes multiple missions:

structural support, as the connection of shell and rotor hub motor end cover, needs to carry the rotor high-speed rotation of the centrifugal force and vibration load;

 Thermal management center: by optimizing the heat dissipation design, build end cover from the internal winding to the path of thermal conductivity of the external environment;

Sealing barrier: in complex condition, such as rail, electric cars, the end cover can resist the invasion of the moisture, dust and chemical corrosive medium; Electromagnetic compatibility interfaces: end cover part of the design should be integrated electromagnetic shielding layer, suppress the high-frequency harmonic disturbance to the surrounding equipment.

Performance dimensions of The Traction Motor End Cover

Mechanical properties of the fatigue strength: to satisfy the 10 ^ 7 times zero flaw under circulating load requirements (refer to the IEC 60034 standard); Dynamic deformation control: under the rated speed, the end cover flange surface axial pulse quantity usually 0.05 mm or less; Impact toughness: – 40 ℃ low-temperature impact energy (KV2) or greater 27 j (for frigid application scenario).

The thermal efficiency of heat transfer: aluminum alloy plate thermal conductivity should be 150 w/(m K) eller højere, with forced air cooling when the temperature control is within 55 K; Thermal expansion coefficients of thermal expansion match: motor cover and frame difference to 1.5 * 10 ^ – 6 / ℃ or less and avoid the structure stress of high-temperature conditions.

The environmental adaptability of salt fog resistance: coastal environment application by 480 h neutral salt spray test (ISO 9227); Seal level: IP67 protection standards can withstand under 1 m water depth soak 30 minutter; Fretting wear resistance: the bearing chamber surface after nitriding treatment, microhardness to achieve HV650 above. Grade three, motor cover hardcore process control parameters of ductile cast iron QT500-7: graphite spheroidization rate is 90% eller højere, pearlite content control in 30-50%; Low-pressure casting process: vacuum degree of the cavity 5 kph or less, to ensure that key parts without shrinkage cavity defects; Aging treatment: 300 ℃ x 6 h to stress annealing, 50 mph or less residual stress. Dynamic stiffness matching parameters of the bearing chamber: the radial stiffness of 5 x 10 ^ 8 or higher n/m, the axial rigidity of 3 x 10 ^ 8 n/m or higher; Modal frequency to avoid: first-order natural frequency to avoid the wheel-rail excitation frequencies (120-180 hz); Thermal deformation compensation: design expansion gap 0.15 0.3 mm (thermal gradient calculation according to the line).

Service monitoring data of the vibration intensity: the use of bearing vibration velocity RMS 2.8 mm/s or less (ISO 10816-3); Temperature threshold: winding end temperature alarm value set to 105 k corresponding insulation class (200); Seal life: fluorine rubber seal replacement cycle 800000 km or more (the equivalent of three-phase).

Pakke af The Traction Motor End Cover

Polybag+Kartonæske+Trækasse/Palle, efter kundens ønske

Virksomhedsprofil

Luoyang Fonyo Heavy Industries Co., Ltd. blev grundlagt i 1998, dækker et område på 72.600㎡, med mere end 300 medarbejdere, 32 teknikere, inklusive 5 senioringeniører, 11 assistentingeniører, og 16 teknikere. Det er blevet vurderet som Luoyang Engineering Technology Center, Luoyang Technology R&D Center, og National High-tech Enterprise i mange gange.
Vores produktionskapacitet er 30,000 tons om året. For tiden, vi producerer hovedsageligt støbt stål, støbejern (gråt jern, duktilt jern, osv.), forarbejdning af færdigt produkt og komponentsamling. produkterne er blevet eksporteret til Rusland, USA, Tyskland, Argentina, Japan, Frankrig, Sydafrika,Italien og andre lande.

Ofte stillede spørgsmål

Q1: Er du producent eller handelsvirksomhed?
EN:Vi er en producent. Vores firma blev grundlagt i 1998, med næsten 30 år i støbeindustrien, et samlet areal på 72.600㎡, med et fabriksbygningsareal på 51.000㎡.
Q2. Hvad er dine vigtigste produkter?
EN: Vi fokuserer primært på stålstøbning, jernstøbning, bearbejdning af færdigt produkt, og komponentmontageproduktion.
Q3: Hvor præcision kan du producere støbedele?
EN: Vi har evnen til at producere støbedele med forskellige støbeprocesser. Produktionen er strengt i overensstemmelse med ISO 9001, ISO 14001 og ISO45001, EN15085, IRIS.
Q4. Kan du producere i henhold til prøverne?
 Ja, vi kan producere efter dine prøver eller tekniske tegninger. Vi kan også bygge tegninger til dig, efter at vi har fået dine prøver.
Q5: Hvordan laver du kvalitetskontrol før levering?
EN: Kvalitetsinspektion er en meget vigtig faktor for at garantere kvaliteten af ​​stålstøbedele. Vi følger efter 3 inspektionstidspunkter under hele produktionsprocessen. Og vi vil levere materialetestrapport, dimensionel prøvningsrapport, og mekaniske egenskaber test rapport til vores kunder før levering.

Hvis du er interesseret i alle produkter, er du velkommen til at kontakte os.
E-mail:[email protected]
Mobil:008615515321683